This is an old revision of the document!


Usage

vcs should be run from the command line. Through the use of command-line options or configuration files its behaviour can be configured to fit your needs.

When run with no arguments, vcs will show the following traits:

  • A capture is taken every 5 minutes. Videos shorter than 5 minutes will be rejected with default options
  • The captures will be placed in a grid, 2-columns wide and as many rows as required
  • Individual captures will have the dimensions of the input video (no thumbnails by default)
  • Output will be PNG format and named like the input file (extension included) plus .png (e.g. $ vcs “some file.avi” will produce some file.avi.png)
  • vcs won't ever overwrite files (unless a bug slips). If the output file exists it will add a numbered suffix before the extension, so if output.png exists it will create output.avi-1.png (or output.avi-2.png, output.avi-3.png and so on)
  • The default colourscheme uses a RGB(175,205,122) (      ) and a SlateGray (      ) footer
    • vcs below 1.11 used a YellowGreen (      ) heading
    • vcs below 1.0.3a used a SandyBrown (      ) footer

There's two ways to decide how many captures are made: at intervals or a fixed number. These correspond to the command-line options -i and -n respectively (long options: --interval and --numcaps)

The fixed number mode is aesthetically preferable because it can always fill the contact sheets, while the interval mode might leave some empty spaces.

Intervals can be specified in number of ways, see Time/Interval syntax for details. To take a capture every minute you could use $ vcs -i 1m file.avi. vcs will show how many captures will make in total while working, e.g.:

Generating capture #1/7 (04:16.15)...
Generating capture #2/7 (08:32.31)...
Generating capture #3/7 (12:48.46)...
Generating capture #4/7 (17:04.62)...
[...]

In this example 7 captures are to be made, 4 have been completed already.

Setting a fixed number on captures is straightforward, just follow the appropriate option with the number of captures, e.g. to make 8 captures: $ vcs -n 8 file.avi.

Note it (obviously) doesn't make sense to use both -n and -i. The last one in the command line will prevail.

The number of columns produced is dictated by the -c (--columns) argument. Follow it by the number of columns.

The number of rows can't be manually set, there will always be as many as needed to accommodate the number of columns and captures.

Size of the captures can be set by defining their height and/or their aspect ratio. Width is always derived, this is by design although by combining height and aspect ratio you can manually set both width and height (explained below). The size of the full contact sheet can't be directly controlled.

To set the capture height use the -H (--height) option followed by the height in pixels or a percentage (with a percentage, height will be computed from the source height).

To set the aspect ratio use the -a (--aspect) option followed by the aspect ratio either as a (floating point) number or a fraction (both 1.33 and 4/3 are valid formats).

To force a certain width combine height and aspect ratio, e.g. if you want your captures to be 300×200 pixels you can use -H 200 -a 300/200 (in case it isn't obvious, an image 200px high and having a 300/200 –same as 3/2, 1.5– aspect ratio must be 300×200 pixels).

Use -A (--autoaspect) to let vcs try to guess aspect ratio. Guesses are only made on well known resolutions (i.e. VCD and DVD family of resolutions), note that for cases in which both a 4:3 and a 16:9 resolution are possible 4:3 is chosen. If it can't be guessed the original aspect ratio will be used.

vcs 1.11 and higher only

The output filename can be set with the -o (–output) option. Repeat for each input filename.
Additionally the file extension of the output filename can also control the file format.

Examples

Save to output.jpg:

$ vcs input.avi -o output.jpg

Save output of file1.avi to output1.jpg, output of file2.avi to output2.png and output of file3.avi to file3.avi.png:

$ vcs file1.avi file2.avi file3.avi -o output1.jpg -o output2

A title like can be added through the -T (--title) option. The title will be displayed in a big font below the meta-information heading.

Example

$ vcs -T "Some title" file.avi

Example contact sheet with title:
Full contact sheet, including a title

See also sections.

See colours for details.

All dates/times in this page are UTC.